Accu-Lites PM42 Breakout Board for Digitrax PM42

The PM42 breakout board brings out all the connections available on the Digitrax PM42 to easy access screw terminals. The PM42 breakout board is setup to accept up to 2 inputs and 4 distinct outputs. Each output uses a set of jumpers that allows you to...

Digitrax UP5 Loconet Universal Panel

Features Give your layout a professionally finished look. Two RJ12 6 pin LocoNet jacks in the back of the panel for hooking up LocoNet devices that use RailSync. Two RJ12 6 pin Throttle jacks in the front of the panel for hooking up throttles and...

Digitrax Decoder Installation Wire, 30 Gauge

Decoder wire for decoder, lighting & signal installations. Features 30 AWG Stranded Wire 90 Feet of Wire, 10' lengths in 9 colors NMRA Colors (Red, Black, Blue, White, Yellow, Orange, Gray, Green, Violet)

Accu-Lites Multi Zone Breakout Board for Digitrax BDL168

BDL168 Multi Zone Breakout Board for EZ wiring! The BDL168 Multi Zone breakout board brings out all the connections available on the Digitrax BDL168 to easy access screw terminals. Multi Zone Operation This design has 4 inputs separate inputs,...

Accu-Lites SE8C Breakout Board for Digitrax SE8C

Breakout board for the Digitrax SE8C. The SE8C breakout board brings out all the connections available on the Digitrax SE8C to easy access screw terminals. This includes the 8 slow motion switch machine drivers, the 8 pushbutton inputs and the 8 sensor...

Accu-Lites Jumpers for PM42 Breakout Board

The Acculites PM42 Breakout Board has only one pair of jumpers included for setting up a reversing section with your PM42. These extra jumpers are for adding more reversing sections when wiring the PM42 Breakout Board. Package contains two jumpers.

Accu-Lites Single Zone Breakout Board for Digitrax BDL168

BDL168 Single Zone Breakout Board for EZ wiring! The BDL168 Single Zone breakout board brings out all the connections available on the Digitrax BDL168 to easy access screw terminals. Single Zone Operation This design has a single input, meaning...

Digitrax Card Edge Connector 44 Pin, (3pcs)

3-Pack of 44-Pin Card Edge Connectors for use with PM4 Series Boards, BDL16 Series Boards and SE8 Series Boards.

Digitrax Booster Terminal Connector Plug

Gray replacement plug for lost or damaged plugs on DB150, DB200+, DCS100 or DCS200.

Digitrax LNRP Xtra LocoNet Repeater Module

The LNRP Xtra LocoNet Repeater Module Isolates and Protects LocoNet Layouts, it allows for greater expansion of the LocoNet system on large installations. If a wiring or signal problems occur on any standard LocoNet section that the LNRP Xtra is...

Digitrax LT1 Decoder & LocoNet Cable Tester

The LT1 is included with all Digitrax Starter Sets. It consists of a harness with 6 conductor Telco type wire and a male plug, a tester with a female 6 conductor jack and a protection resistor. If you make your own LocoNet cables, this is a handy device...

Digitrax PSYC52 Y Cable for PS2012

Use to connect multiple DCC Power Boosters to a single power supply such as the Digitrax PS2012 or Crest 55465. Features For use with PS2012 power supplies or similar. Each Y Cable comes with dual 5 amp protected outputs Up to 24 volt AC...

Digitrax Throttle Battery Cover

Replacement for current model throttle battery compartment covers.

Digitrax UP6Z - LocoNet Universal Panel & Z-Scale Voltage Reducer

LocoNet Universal Panel and 3 Amp Z Scale Voltage Reducer 6 LocoNet Jacks for use with all scales Reduces track voltage by 4 or 6 volts at 3 amps for safer Z Scale locomotive opreration with Digitrax...